Unfortunately I needed a bit that I didn't already own. That is that they weren't close enough the the bore to properly engage the front sight plunger. The plunger notches were not deep enough. I threaded the adapter onto my Draco and encountered the first problem. The threads were a little sharp but the burrs were no where near as bad as on the FH. It has 4 plunger notches located at 12, 3, 6 and 9 o'clock. As I previously stated it weighs a hefty. I didn't measure the specs other than wieght since they don't really matter with the FH attached. It is solid and screws together well with no play. It was very obviously made someplace where they speak something-ese. The internal cone appears to be chromed although is has a roughly machined texture. Looking at the rear of the FH the notches are at 6:30 and 11:30 with the wrench flats at 3:00 and 9:00. The internal and external threads are both sharp and have lots of burrs. After I wiped it down and cleaned off all of the CLP I noticed that the t-shirt rag I was using was shredded. I gave it a good scrub with CLP and a stiff nylon brush to remove all goo. The machine work isn't bad and you won't really notice any issues until you disassemble and start cleaning. It is blued with a distinct brownish tint. The FH was covered in a half dried, yellow oily goo. I thought "It's just a FH, how much could it weigh?" Yeah a half pound of chunky goodness. I don't remember who mentioned it but they pointed out the weight and affect on balance that the 4-Piece had. The very first thing I noticed was the weight. Both the 4-Peice and adapter were sealed in their own plastic bags. Real deal Bulgarian or otherwise.ĪPEX sent USPS Priority. No way could I have dropped $105 on the FH alone. These allow the use of AK74 type muzzle devices to be used on your AK47.ĭamn, that was expensive. Their description: Thread adapter for 24mm to 1/14 Excellent quality thread adapter for the AK47. I needed an adapter so I picked up theirs. It can be used on the 7.62x39 rifles with the use of a thread adapter which we sell. This is the best, most affective muzzle brake ever made for the AK type rifle. Their description: Exact copy of the Bulgarian four piece flash hider. APEX readily admits that this item is a copy but states that is meant for use on firearms, not airsoft. I wanted something that would provide flash suppression and increase functional reliability of my 7.62 Draco pistol. This is by far the most common caliber/barrel combination for 7.62×39 the world over so it seemed appropriate.I recently picked up a Bulgarian Type, Four Piece Muzzle Brake from APEX. Going Loud With Itįor my shade tree subjective testing I chose a 7.62×39 FrankenGun with a 16″ barrel. While this is no 8″ suppressor hanging off the end of a rifle, I still recommend double checking muzzle alignment before pulling the trigger for the first time. This makes little difference with a stubby slant brake, but the longer the muzzle device is the more issues you can run into. Though this is far from insurmountable, it's definitely something that you should be aware of.ĭue to the inconsistency of eastern-block manufacturing, threads aren't always cut concentric to the bore with AKs. Combined with the fact that it has to be properly timed to be effective, this adds a layer of complication during installation. There are generously sized wrench flats on the base that allow the use of an armorers tool or even a crescent wrench for installation or removal–bear in mind that if you have a tool solely for standard 5.56 A2 devices and their ilk it will be too small.Īs you have no doubt have already ascertained, the SuperComp XL utilizes a crush washer for installation rather than achieving alignment with the plunger pin on an AK front sight block (FSB). The compensator by itself is just a hair under 3″ long (2.996″ to be exact–without the crush washer) and adds 2.4″ to the length of the rifle. There are 14 ports on this muzzle monster six on each side for recoil reduction and two on the top to aid in fighting muzzle rise under recoil. You'll be able to tell immediately where the ‘XL' comes from. From where I sit, producing one for 7.62×39 by threading in 14x1LH seems like a natural progression. Some customers have been utilizing the 7.62N versions for. The SuperComp XL is available in common thread patterns like 1/2×28 for 5.56 guns and 5/8×24 for 7.62N blasters, but most recently they've added 14x1LH for the Commie carbines–this thread pattern is so new that it's not yet available for purchase on their website.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |